Go to Homepage
Best Welding Magnets Compared for 2026: Squares and Holders

Best Welding Magnets Compared for 2026: Squares and Holders

Best welding magnets compared: five squares and holders rated up to 90 lb, with angles, size and fit notes. Read the guide and choose your holder.

Share

Five magnetic welding squares and holders compared by rated pull force, angle options, switch design and size for shop and field jobs

Holding two pieces of steel at a true angle while you tack them is one of the most common jobs in a fabrication shop, and a good welding magnet turns it into a one-person task. The wrong one slips, drifts off square, or lets go the moment a plate gets heavy.

This comparison looks at five options using the criteria that matter most. Rated pull force sets how much steel a magnet can be expected to hold. Angle options decide whether it handles only right angles or also 45 and 135 degree joints. Form factor, meaning a switched square, a single fixed holder or a multi-pack, decides how it fits your workflow.

Pull-force numbers are manufacturer ratings, typically measured under ideal conditions such as thick, flat steel, so results on rusty, painted or thin material will be lower. Keep magnets away from direct heat as well, since heating weakens a magnet’s grip.

ProductAmazon ratingBest forLink
Strong Hand Tools Adjust-O Heavy Duty Magnetic Welding Square MSA46-HD ★★ 4.5/5
(1,119)
Heavy plate, one-person tackingView →
Hobart 770064 Magnetic Welding Holder, X-Large★ 3.9/5
(6)
General fabrication, mixed anglesView →
Hobart 770063 Welding Magnetic Holder, Large★ 4.4/5
(65)
Sheet metal and tubingView →
PGN 50 LB Welding Magnet Holder 4-Pack★ 4.4/5
(133)
Frames needing several magnetsView →
Lincoln Electric Magnetic Welding Parts Holder, Medium, KH920★ 4.0/5
(1)
Light sheet and tubeView →

Strong Hand Tools Adjust-O Heavy Duty Magnetic Welding Square MSA46-HD

Click to view Strong Hand Tools Adjust-O Heavy Duty Magnetic Welding Square MSA46-HD

The Strong Hand Tools Adjust-O MSA46-HD is a switched magnetic square with a manufacturer rating of 90 lb of pull force, measured on 3/8 inch steel along the magnet’s longest side. It holds work at 45 and 90 degrees and uses rare earth magnets in a fully enclosed body, which the maker says makes cleaning easier.

The on/off switch lets you place the square, tack the joint, then release the magnet without prying it off. At roughly 4 3/8 by 3 3/4 by 1 1/8 inches and 1.5 lb, it is bulkier than the plain arrow holders in this group, but that mass comes with the highest rated pull here. Buyers often mention it as a dependable single magnet for heavier plate and frame work.

★ 4.5/5 · 1,119 Amazon ratings✓ Best for: Heavy plate, one-person tacking✗ Not ideal for: Occasional light-duty hobby useCheck Price on Amazon →

Hobart 770064 Magnetic Welding Holder, X-Large

Click to view Hobart 770064 Magnetic Welding Holder, X-Large

The Hobart 770064 X-Large magnetic holder is rated by the manufacturer for up to 75 lb of pulling force and holds steel pieces at 45, 90 and 135 degrees. That angle range covers square corners, mitered joints and obtuse bends from a single tool, which is the main appeal of this style of holder over a basic right-angle square.

It sits in the middle of this comparison on rated strength, above the 50 lb class and below the 90 lb switched square, so it suits general fabrication on medium plate, angle iron, tube frames and repair work where a switched magnet is not needed.

★ 3.9/5 · 6 Amazon ratings✓ Best for: General fabrication, mixed angles✗ Not ideal for: Needing a switched releaseCheck Price on Amazon →

Hobart 770063 Welding Magnetic Holder, Large

Click to view Hobart 770063 Welding Magnetic Holder, Large

The Hobart 770063 Large magnetic holder is rated by Hobart for up to 50 lb of holding power and is described as holding steel pieces at 45, 90 and 135 degree angles. It is the step down from the X-Large model in the same line, trading 25 lb of rated pull for a lighter-duty rating that is still enough for many everyday jobs.

A 50 lb rating is a sensible fit for sheet metal, light plate, small brackets and tube work, and it leaves room to move up to the larger model when parts get heavier. Because it is a single magnet, you will typically want a second one to support longer pieces. Hobart describes it as a multi-purpose holder, so it can also serve for general positioning around the shop.

★ 4.4/5 · 65 Amazon ratings✓ Best for: Sheet metal and tubing✗ Not ideal for: Heavy plate workCheck Price on Amazon →

PGN 50 LB Welding Magnet Holder 4-Pack

Click to view PGN 50 LB Welding Magnet Holder 4-Pack

This PGN set contains four arrow-style welding magnet holders, each rated at 50 lb and sized for 45, 90 and 135 degree angles. Four magnets in one pack changes how you work, since you can hold both ends of a long joint, fixture a box or frame at several corners at once, or share the set between two workstations.

Buyers often mention that a multi-pack is more useful than one stronger magnet when assembling frames and boxes. Keep in mind that the 50 lb figure is a per-magnet manufacturer rating, and thin material or tubing may need more than one magnet for a secure hold. It is a practical choice when quantity and flexibility matter more than the highest single-magnet rating.

★ 4.4/5 · 133 Amazon ratings✓ Best for: Frames needing several magnets✗ Not ideal for: Single heavy-plate jointsCheck Price on Amazon →

Lincoln Electric Magnetic Welding Parts Holder, Medium, KH920

Click to view Lincoln Electric Magnetic Welding Parts Holder, Medium, KH920

The Lincoln Electric KH920 is a medium-size magnetic welding parts holder used to hold sheet and tube at 45, 90 and 135 degrees. It uses a ferrite magnet and works on ferrous metal only, so it will not grip non-ferrous metals such as aluminum.

As the medium size in Lincoln’s range, it is the lightest-duty holder in this group, which makes it a fit for lighter sheet, thin angle and small assemblies rather than heavy plate. Lincoln Electric is a name many welders recognize, and the KH920 is widely stocked by hardware and welding retailers, so it is easy to add a second or third magnet to a shop kit when you need extra support points.

★ 4.0/5 · 1 Amazon ratings✓ Best for: Light sheet and tube✗ Not ideal for: Heavy plate holdingCheck Price on Amazon →

Conclusions

The Strong Hand Tools Adjust-O Heavy Duty Magnetic Welding Square MSA46-HD is the pick for heavy work, with the highest rated pull here at 90 lb and a switch that releases the load cleanly. It is limited to 45 and 90 degree angles, so mixed-angle jobs may call for a different holder. … read more

The Hobart 770064 Magnetic Welding Holder, X-Large suits welders who want 45, 90 and 135 degree angles with a 75 lb rating and no switch to manage. It sits between the 90 lb square and the 50 lb holders, which makes it a sound all-round shop choice for medium plate and frames. … read more

The Hobart 770063 Welding Magnetic Holder, Large fits sheet metal, tubing and light plate with its 50 lb rating and 45, 90 and 135 degree angles. Choose it when parts are modest in weight, and step up to the X-Large model if you handle heavier steel often. … read more

The PGN 50 LB Welding Magnet Holder 4-Pack gives you four 50 lb rated magnets at 45, 90 and 135 degrees, which helps with frames, boxes and long seams that need several points of support. It is a practical choice when quantity matters more than the highest single-magnet rating. … read more

The Lincoln Electric Magnetic Welding Parts Holder, Medium, KH920 is a compact option with 45, 90 and 135 degree angles. It fits light sheet, tube and small assemblies, but heavier plate is better served by one of the higher-rated holders in this comparison. … read more

Frequently Asked Questions

How much steel can a welding magnet actually hold?

Pull-force figures are manufacturer ratings, typically measured on thick, flat, clean steel. Rust, paint, scale, thin material or curved surfaces reduce real holding force, so treat the rating as a best case and add a second magnet for heavy or awkward parts.

Do welding magnets lose strength when they get hot?

Yes, heat can weaken a magnet. Some strength may return as it cools, but exceeding the magnet's temperature limit can cause permanent loss. Place magnets away from the weld zone, avoid hot steel, and check the maker's guidance for your model.

What is the difference between a switched square and a fixed holder?

A switched square has an on/off control, so you can set it down, tack the joint and release it easily. A fixed holder is always magnetic, which keeps it simple and often allows more angles, but you pull it off the steel by hand.

Can welding magnets hold aluminum or stainless steel?

Magnets grip only ferrous metals. Aluminum and copper are not attracted at all, and many stainless grades hold weakly or not at all. For those materials, use clamps or fixtures instead of relying on a magnetic holder.

How many welding magnets do I need for a project?

Most joints are easier with two magnets, one at each end of the seam. Boxes and frames may need four or more. A multi-pack is useful for larger assemblies, while one strong switched square can cover quick single-corner tacking.

We use cookies. Analytics cookies help us understand how visitors use this site. See our Privacy Policy for details.