Go to Homepage
Best Step Drill Bit Sets Compared for 2026: 5 Top Picks

Best Step Drill Bit Sets Compared for 2026: 5 Top Picks

Best step drill bit sets compared for sheet metal, conduit boxes and HVAC work. See size ranges and materials, then pick the right set for you.

Share

Five step drill bit sets compared by size range, bit material and shank so you can match a set to your sheet metal and conduit box holes

If you cut holes in sheet metal, conduit boxes, electrical enclosures or ductwork, a step drill bit set saves you from carrying a full index of twist bits. One cone-shaped bit makes many hole sizes, leaves a fairly clean edge in thin material and rarely wanders on a smooth panel.

Sets are not interchangeable, though. The criteria that matter most are the size range and number of bits, because a set that tops out at 7/8 inch will not help with a 1-1/8 inch knockout. Next come the bit material and coating, then the shank style, since a hex shank suits impact drivers and a three-flat shank suits drill chucks.

Below you will find five sets compared on those points, with who each one suits and who should skip it. Check your most common hole sizes first, then match them to the ranges listed so you buy the set that covers your work.

ProductAmazon ratingBest forLink
DEWALT Impact Ready Step Drill Bit Set DWA1790IR, 3 Piece ★★ 4.8/5
(1,328)
Impact driver sheet metal workView →
IRWIN Unibit Step Drill Bit Set 10502CB, 3-Piece★ 4.4/5
(70)
Familiar Unibit layout, electriciansView →
Lenox Vari-Bit Step Drill Bit Kit 30889889, 3 Piece★ 4.6/5
(31)
Reaching 1 inch holesView →
Milwaukee 4-Piece Step Drill Bit Set 48-89-9223★ 4.6/5
(57)
Large conduit and panel holesView →
NEIKO 10197A Titanium Step Drill Bit Set, 5 Piece★ 4.5/5
(18,453)
Maximum sizes in one setView →

DEWALT Impact Ready Step Drill Bit Set DWA1790IR, 3 Piece

Click to view DEWALT Impact Ready Step Drill Bit Set DWA1790IR, 3 Piece

The DEWALT DWA1790IR is a three-bit set covering hole sizes from 1/8 inch up to 7/8 inch. The bits are titanium nitride coated and each one has a 1/4 inch hex shank, so they drop straight into an impact driver or a drill with a quick-change chuck.

The set is sold as part of DEWALT’s Impact Ready line, which the maker describes as suited to both impact drivers and rotary drills. The bits use a split-point tip to help start a hole without a pilot, and the steps carry laser-engraved size markings, which makes it quicker to see which step you are on when sizing a hole in a box or enclosure.

The three bits overlap in range, with small, medium and larger bits covering 1/8 inch to 1/2 inch, 3/16 inch to 1/2 inch and 3/16 inch to 7/8 inch. That suits trim, switch and small conduit work well. It stops at 7/8 inch, so larger knockout sizes need a bigger set.

★ 4.8/5 · 1,328 Amazon ratings✓ Best for: Impact driver sheet metal work✗ Not ideal for: Holes over 7/8 inchCheck Price on Amazon →

IRWIN Unibit Step Drill Bit Set 10502CB, 3-Piece

Click to view IRWIN Unibit Step Drill Bit Set 10502CB, 3-Piece

The IRWIN 10502CB is a three-piece step drill set covering hole sizes from 1/8 inch to 3/4 inch. It uses a 1/4 inch hex shank on the bits, which fits impact drivers as well as standard drill chucks that grip a hex.

The set includes the numbered Unibit sizes, with the third bit running from 1/4 inch to 3/4 inch in 1/16 inch steps, a layout many electricians know from years of Unibit use. The three bits together give a spread from small pilot-size holes up to common conduit connector sizes.

Its three bits together make a compact kit for sheet metal, thin steel and aluminum. Its range tops out at 3/4 inch, so buyers who need larger holes should look at a set with bigger steps.

★ 4.4/5 · 70 Amazon ratings✓ Best for: Familiar Unibit layout, electricians✗ Not ideal for: Large knockout holesCheck Price on Amazon →

Lenox Vari-Bit Step Drill Bit Kit 30889889, 3 Piece

Click to view Lenox Vari-Bit Step Drill Bit Kit 30889889, 3 Piece

The Lenox 30889889 is a three-bit Vari-Bit kit covering 1/8 inch to 1 inch overall, which is the widest top size among the three-piece sets here. The bits are high-speed steel with a steam oxide finish, two flutes and a 135 degree split-point tip for starting holes without a center punch.

The kit contains the VB1, VB2 and VB3 bits. The VB1 steps from 1/8 inch to 1/2 inch, the VB2 from 1/2 inch to 1 inch and the VB3 from 1/4 inch to 3/4 inch. That layout means the middle bit picks up where the smallest leaves off, so you can reach 1 inch holes without moving to a four-piece set.

Each bit has a three-flat shank that grips in a standard drill chuck without slipping. This is a good fit for people who mostly use a drill rather than an impact driver and who need to reach the common 1 inch range for conduit and cable fittings in sheet steel or aluminum.

★ 4.6/5 · 31 Amazon ratings✓ Best for: Reaching 1 inch holes✗ Not ideal for: Impact driver hex useCheck Price on Amazon →

Milwaukee 4-Piece Step Drill Bit Set 48-89-9223

Click to view Milwaukee 4-Piece Step Drill Bit Set 48-89-9223

The Milwaukee 48-89-9223 is a four-piece step set made of high-speed steel with a black oxide finish, supplied with a carrying case. It is the set here that reaches the largest hole sizes, going up to 1-3/8 inch with the biggest bit.

The set includes the number 1 bit running from 1/8 inch to 1/2 inch, the number 4 bit from 3/16 inch to 7/8 inch, the number 12 bit from 7/8 inch to 1-3/8 inch, and a number 7 bit. Milwaukee describes the bits as dual-flute with a three-flat Secure-Grip shank and a Rapid Strike tip meant to start holes accurately.

The wider top end makes this set a practical choice for panel and enclosure work, where holes for larger conduit connectors come up alongside small ones. The step sizes on the larger bits are spaced further apart, so check that your most common hole sizes fall on a step rather than between two.

★ 4.6/5 · 57 Amazon ratings✓ Best for: Large conduit and panel holes✗ Not ideal for: Fine small-hole workCheck Price on Amazon →

NEIKO 10197A Titanium Step Drill Bit Set, 5 Piece

Click to view NEIKO 10197A Titanium Step Drill Bit Set, 5 Piece

The NEIKO 10197A is a five-piece set made of high-speed steel with a titanium coating, offering 50 SAE hole sizes in total from 1/8 inch to 1-3/8 inch. That combination of piece count and range is the broadest of the sets compared here.

With five bits instead of three or four, each bit covers a narrower span, which means more step sizes to choose from and less distance between the sizes. This helps when you need a hole that falls between common sizes, for example when fitting a particular grommet or cable gland in a duct or panel.

The bits use a tri-flat shank for secure grip in a standard drill chuck, and retailers list them as two-flute step bits. NEIKO sells many step sets with different piece counts, so confirm the 10197A model and the SAE sizing when you buy. It suits those who want maximum range and sizes in one set rather than a small, specialized one.

★ 4.5/5 · 18,453 Amazon ratings✓ Best for: Maximum sizes in one set✗ Not ideal for: Impact driver usersCheck Price on Amazon →

Conclusions

The DEWALT DWA1790IR is our editor’s pick for most electrical and HVAC buyers who use an impact driver. Its titanium nitride coating, 1/4 inch hex shanks and 1/8 to 7/8 inch range cover typical box and panel holes. Choose a bigger set if you need larger knockouts. … read more

The IRWIN 10502CB suits electricians who already like the Unibit step layout and want a three-piece set from 1/8 to 3/4 inch with hex shanks. It is a good match for small and medium conduit holes, but not if you regularly cut holes above 3/4 inch. … read more

The Lenox 30889889 Vari-Bit kit is the pick for drill users who need to reach 1 inch holes with only three bits. Its high-speed steel bits have a steam oxide finish and three-flat shanks. It is less suited to impact drivers that take hex-shank bits. … read more

The Milwaukee 48-89-9223 four-piece set is the choice when your work includes larger holes up to 1-3/8 inch, such as bigger conduit connectors in panels. It comes with a case. … read more

The NEIKO 10197A five-piece titanium coated set fits buyers who want the most step sizes and range from 1/8 to 1-3/8 inch in one box. Its tri-flat shanks are made for a drill chuck, so it suits drill users more than impact driver users. … read more

Frequently Asked Questions

How do step drill bits compare with twist bits for sheet metal?

Step bits cut a round hole in thin sheet in one pass and cover many sizes with one bit, and they tend to leave a cleaner edge. Twist bits can grab or leave an oval hole in thin metal. Twist bits remain the better choice for thicker material and deeper holes.

How do I choose between a three-piece and a five-piece step bit set?

Start with the hole sizes you cut most. More bits give more sizes and a wider range, but a three-piece set can be enough if your holes are under 7/8 inch. Check each set's listed range against the sizes of your conduit connectors and grommets.

Should I use cutting fluid when drilling with a step bit?

Yes, a few drops of cutting oil on the bit reduce heat and help the cutting edges last, especially in steel. Clamp the sheet firmly, start at a moderate speed and back the bit out occasionally to clear chips and keep the hole edge clean.

Do step drill bits work in an impact driver?

Only bits with a 1/4 inch hex shank fit an impact driver chuck, and only if the maker says they are suited to it. Bits with a three-flat shank are designed for a drill chuck, so check the shank type before you use a set with an impact driver.

How do I stop a step bit from wandering when starting a hole?

Use a bit with a split-point tip, or mark the spot with a center punch first. Clamp the workpiece, hold the drill square to the surface and begin at a low speed until the tip bites, then increase speed as the first step cuts.

We use cookies. Analytics cookies help us understand how visitors use this site. See our Privacy Policy for details.