Go to Homepage
Best Midi Wood Lathes Compared for 2026: 5 Top Picks for Turners

Best Midi Wood Lathes Compared for 2026: 5 Top Picks for Turners

Best midi wood lathes compared for 2026: five 12-inch benchtop models for bowls, spindles and pens, side by side. See the specs and pick yours.

Share

Five 12-inch variable-speed benchtop lathes compared on motor, speed range, capacity and included accessories so you can choose the right one

A full-size lathe can eat a whole corner of the shop and a good chunk of the budget, while the cheapest mini lathes run out of power the moment you mount a bowl blank. Midi lathes with a 12-inch swing sit in the middle: they fit on a sturdy bench, yet they can rough out bowls, turn spindles and handle pens and small hollow forms.

Four things separate one midi lathe from another. First is motor power and how it is delivered, because torque at low speed matters when a blank is out of balance. Second is the speed range and how you change speed, by moving a belt or by turning a dial. Third is capacity between centers and whether the bed can be extended. Fourth is the spindle and what comes in the box, since a lathe that needs extra purchases before it can turn anything costs more than it seems.

Below you will find five 12-inch benchtop lathes compared on those points, with specs drawn from manufacturer and retailer pages, the honest trade-offs of each, and a clear pick for most turners.

ProductAmazon ratingBest forLink
JET 12-Inch x 21-Inch Variable-Speed Wood Lathe JWL-1221VS ★★ 4.4/5
(667)
Serious all-round bowl turnersView →
RIKON 70-150VSR 12-Inch Variable Speed Midi Lathe★ 4.6/5
(107)
Turners wanting digital speed readoutView →
RIKON 70-100 12-Inch by 16-Inch Mini Lathe★ 4.3/5
(82)
Budget-minded small-project turnersView →
PSI Woodworking KWL-1218VS Turncrafter 12-Inch Variable Speed Midi Lathe★ 4.4/5
(85)
Value-focused buyers wanting accessoriesView →
VEVOR 12 x 18 Inch Variable Speed Wood Lathe 1 HP★ 3.9/5
(578)
Budget buyers wanting 18-inch capacityView →

JET 12-Inch x 21-Inch Variable-Speed Wood Lathe JWL-1221VS

Click to view JET 12-Inch x 21-Inch Variable-Speed Wood Lathe JWL-1221VS

The JET JWL-1221VS pairs a 1 HP, 115-volt motor with a 12-1/2 inch swing over the bed and about 20-1/4 inches between centers. Its electronic variable speed runs from 60 to 3,600 RPM, so you can start a rough bowl blank very slowly and still reach high speeds for pen blanks and small spindles. The cast iron construction adds mass that helps damp vibration on a benchtop.

The spindle is 1 inch by 8 TPI with a Morse No. 2 taper, which matches the large range of chucks and drive centers made for that standard. The headstock has 24 indexing positions for drilling, sanding or carving evenly spaced detail, and the tailstock quill has 2-1/4 inches of travel. The tool rest is 6 inches wide, with a 10-inch version also available. The trade-offs are that the stand is sold separately, as is the 22-inch bed extension, so plan on a solid bench or a matching stand.

★ 4.4/5 · 667 Amazon ratings✓ Best for: Serious all-round bowl turners✗ Not ideal for: Buyers wanting a stand includedCheck Price on Amazon →

RIKON 70-150VSR 12-Inch Variable Speed Midi Lathe

Click to view RIKON 70-150VSR 12-Inch Variable Speed Midi Lathe

The RIKON 70-150VSR is a 12-inch by 16-1/2 inch midi lathe with a 1 HP, 115-volt motor drawing about 6 amps. Electronic speed control covers roughly 250 to 3,200 RPM across three ranges, 250 to 850, 430 to 1,450 and 950 to 3,200, and a digital readout shows the speed you are running. Forward and reverse rotation is built in, which helps when sanding or when working with certain chuck setups.

The bed has machined ends so extensions can be added later to lengthen the spindle capacity. In the box you get a spur center, live center, 3-inch faceplate, 6-inch tool rest with a 1-inch post, knock-out bar, wrenches and a tool holder, so you can begin turning without much extra shopping. The trade-offs are that the three ranges are selected by moving the belt, so changing between the extremes takes a moment, and the 16-1/2 inch capacity is shorter than that of the JET.

★ 4.6/5 · 107 Amazon ratings✓ Best for: Turners wanting digital speed readout✗ Not ideal for: Long spindle work unextendedCheck Price on Amazon →

RIKON 70-100 12-Inch by 16-Inch Mini Lathe

Click to view RIKON 70-100 12-Inch by 16-Inch Mini Lathe

The RIKON 70-100 is an older, simpler design that changes speed by moving the belt across stepped pulleys, not with electronic control. According to the manual it offers six fixed speeds: 430, 810, 1,230, 1,810, 2,670 and 3,900 RPM. Swing over the bed is 12 inches, with 16 inches between centers and about 9-1/2 inches of swing over the tool rest base.

The motor is rated at 1/2 HP on 115 volts, so it has less muscle than the 1 HP machines here and suits lighter work such as pens, small bowls, spindles and handles. The spindle nose is 1 inch by 8 TPI with a Morse No. 2 taper in both headstock and tailstock, the tailstock ram travels 2-1/2 inches, and the spindle has a 3/8 inch through-hole. Net weight is 88.5 pounds. The main trade-offs are that you must open the cover to change speed and that you cannot dial in an in-between speed, which makes it a poor fit for large, out-of-balance blanks.

★ 4.3/5 · 82 Amazon ratings✓ Best for: Budget-minded small-project turners✗ Not ideal for: Large bowl roughingCheck Price on Amazon →

PSI Woodworking KWL-1218VS Turncrafter 12-Inch Variable Speed Midi Lathe

Click to view PSI Woodworking KWL-1218VS Turncrafter 12-Inch Variable Speed Midi Lathe

The PSI Woodworking KWL-1218VS is a 12-inch swing lathe with 18 inches between centers and a cast iron base. Speed is variable from 500 to 3,800 RPM in two belt positions, 500 to 1,800 RPM in the low position and 1,950 to 3,800 RPM in the high one. The spindle is 1 inch by 8 TPI with a Morse No. 2 taper, the tailstock also takes a Morse No. 2, and the headstock offers 24 indexing positions with spindle locking.

The bundle is generous: a ball bearing live center, two tool rests of 6 and 12 inches, a spare drive center, a 3-inch faceplate, a tool storage rack and a work light on a flexible cable. The machine weighs about 106 pounds, which gives reasonable stability on a bench. Trade-offs to note are the belt change needed to move between the two speed ranges, a lowest speed of 500 RPM that is faster than the JET or RIKON 70-150VSR can run, and a bed that is shorter than the JET. That higher floor means extra care when starting heavy bowl blanks.

★ 4.4/5 · 85 Amazon ratings✓ Best for: Value-focused buyers wanting accessories✗ Not ideal for: Slow-speed heavy roughingCheck Price on Amazon →

VEVOR 12 x 18 Inch Variable Speed Wood Lathe 1 HP

Click to view VEVOR 12 x 18 Inch Variable Speed Wood Lathe 1 HP

The VEVOR 12 x 18 inch lathe is a 1 HP benchtop model running on 110-volt power, with a 12-inch swing over the bed and 18 inches between centers. It uses a brushless DC motor with speed adjustable from 0 to 3,800 RPM, so there are no belt changes, and the body is cast iron. For the money-conscious turner it offers the same swing as the pricier machines plus the 18-inch capacity that suits spindles, table legs and baseball bats.

The trade-offs come from the price tier. Buyers often mention that a lower-cost machine has less brand support and fewer matching accessories than the established turning brands, and the brushless motor and cast iron body are the main reasons to consider it. It suits a turner who wants electronic speed control and long spindle capacity without a premium outlay, and it is less suited to someone who wants a long-established service network behind the machine.

★ 3.9/5 · 578 Amazon ratings✓ Best for: Budget buyers wanting 18-inch capacity✗ Not ideal for: Buyers wanting included standCheck Price on Amazon →

Conclusions

The JET JWL-1221VS is the best all-round choice here for turners who want real power and a very low starting speed. Its 1 HP motor, 60 to 3,600 RPM range and 24-position indexing suit bowls, spindles and pens, though you will need to supply a stand or a sturdy bench. … read more

The RIKON 70-150VSR suits turners who like seeing exactly what speed they are running. It combines a 1 HP motor, a digital readout and reverse with a solid starter accessory set, but its 16-1/2 inch capacity is shorter and speed changes between ranges need a belt move. … read more

The RIKON 70-100 is the pick for light-duty work such as pens, small bowls and spindles. It is an older fixed-speed design with six belt-driven speeds and a 1/2 HP motor, so it will struggle with big, unbalanced blanks, but it remains compact at 88.5 pounds. … read more

The PSI Woodworking KWL-1218VS Turncrafter gives you 18 inches between centers and a long list of included accessories, including two tool rests and a work light. Its 500 RPM lowest speed and two-position belt change make it less ideal for large roughing, but it is strong value for general turning. … read more

The VEVOR 12 x 18 Inch 1 HP lathe appeals to buyers who want a brushless motor, 0 to 3,800 RPM stepless control and 18 inches between centers at a lower outlay. It is less suited to buyers who want an established service network. … read more

Frequently Asked Questions

What size lathe is a midi lathe?

Midi lathes in this comparison have about a 12-inch swing over the bed and between 16 and 21 inches between centers. They sit above mini lathes for power and capacity but weigh far less than floor-standing machines, so they fit on a workbench.

Do I need a variable-speed lathe for turning bowls?

It helps a lot. Bowl blanks often start out of balance and need a slow speed, then faster speeds for finishing. The JET starts at 60 RPM and the RIKON 70-150VSR at about 250 RPM, while the RIKON 70-100 is limited to six belt-set speeds starting at 430 RPM.

What spindle thread do these midi lathes use?

The JET JWL-1221VS, RIKON 70-100 and PSI KWL-1218VS all use a 1 inch by 8 TPI spindle nose with a Morse No. 2 taper, so most chucks and drive centers made for that size will fit.

Does the JET JWL-1221VS come with a stand?

No. The stand is an optional extra, as is the 22-inch bed extension. Mount the lathe on a heavy, rigid bench or buy the matching stand, since a 12-inch swing lathe needs mass underneath it to stay steady.

Can a midi lathe handle spindle work longer than its bed?

Only up to the distance between centers, which ranges from 16 inches on the RIKON 70-100 to about 20-1/4 inches on the JET. The RIKON 70-150VSR bed has machined ends so extensions can be added to increase the spindle capacity.

We use cookies. Analytics cookies help us understand how visitors use this site. See our Privacy Policy for details.